Author Topic: Air Access 18  (Read 4379 times)

Offline azslow3

  • Administrator
  • Hero Member
  • *****
  • Posts: 1706
Re: Air Access 18
« Reply #15 on: April 27, 2024, 11:47:10 PM »
Thanks! Preliminary, from the log, the mixer is sending "filter" for Gate and Compressor when not asked explicitly and I am somehow not prepared for that. I will try to fix, but not before Monday-Tuesday.

Offline azslow3

  • Administrator
  • Hero Member
  • *****
  • Posts: 1706
Re: Air Access 18
« Reply #16 on: May 03, 2024, 03:34:39 PM »
Can you download new debug version, from the same location, and check if it works. If not, please send me new log again.

Offline Tomecki

  • Newbie
  • *
  • Posts: 17
Re: Air Access 18
« Reply #17 on: May 05, 2024, 11:06:50 AM »
The error still occurs. I am sending the log.

Offline azslow3

  • Administrator
  • Hero Member
  • *****
  • Posts: 1706
Re: Air Access 18
« Reply #18 on: May 06, 2024, 11:45:17 AM »
I think I have not uploaded changed debugging version, sorry. Can you try again?

If that start to be too boring, we can make an appointment online, so I can change things and you immediately check the result.

Offline Tomecki

  • Newbie
  • *
  • Posts: 17
Re: Air Access 18
« Reply #19 on: May 06, 2024, 04:00:25 PM »
Testing is never boring, but if you prefer, we can meet online. I downloaded the file and am sending the log. The error window looks practically the same.

Offline azslow3

  • Administrator
  • Hero Member
  • *****
  • Posts: 1706
Re: Air Access 18
« Reply #20 on: May 07, 2024, 12:04:24 AM »
We will try one more time tomorrow, if that still doesn't work we will have to go online... But I will try to put more debugging info into next version.

Offline azslow3

  • Administrator
  • Hero Member
  • *****
  • Posts: 1706
Re: Air Access 18
« Reply #21 on: May 07, 2024, 02:13:33 PM »
Lets try again. This time the log file must be bigger and I hope will indicate the problem.

Offline Tomecki

  • Newbie
  • *
  • Posts: 17
Re: Air Access 18
« Reply #22 on: May 07, 2024, 04:16:52 PM »
So, here is the log:

Offline azslow3

  • Administrator
  • Hero Member
  • *****
  • Posts: 1706
Re: Air Access 18
« Reply #23 on: May 07, 2024, 04:57:38 PM »
At least I have understood the was a bug in the attempt to fix the problem. So please try again, hopefully it works now.

Offline Tomecki

  • Newbie
  • *
  • Posts: 17
Re: Air Access 18
« Reply #24 on: May 08, 2024, 12:51:20 PM »
Now the situation is different. If I save the scene with the standard version of the application, the new version loads it and reports no errors. It also appears that at least some of the parameters are restored correctly. I will test it further to see if everything loads. The situation is different when loading a scene saved with a new version of the program. Then the following message appears: "AZ AOSC  dialog  Verification failed for '/config/chlink'". I am sending the log in the attachment.

Offline azslow3

  • Administrator
  • Hero Member
  • *****
  • Posts: 1706
Re: Air Access 18
« Reply #25 on: May 08, 2024, 06:40:41 PM »
The fix has triggered side effect in saving, please try just uploaded version.

Offline Tomecki

  • Newbie
  • *
  • Posts: 17
Re: Air Access 18
« Reply #26 on: May 08, 2024, 11:32:59 PM »
It seems to be working now. I guess because I got an error with channel 10 when I tried to load one of the scenes, but then I couldn't reproduce the problem by also loading the same scene. I also tried completely rearranging the mixer by changing the settings for channels, equalizer, compressor, gate, inserts, effects, routing and everything in the "setup" section and the scene loads correctly.
Thank you very much for your time.

Offline azslow3

  • Administrator
  • Hero Member
  • *****
  • Posts: 1706
Re: Air Access 18
« Reply #27 on: May 09, 2024, 12:33:08 AM »
Thanks for patience, I will upload release version soon. But you can use debug version normally, the only difference is that release version does not write the log.

Just to make it clear, the problem is a kind of bug in the mixer firmware. For 2 parameters it replies with extra information, so AZAOSC had to be adopted. The new version will work also if they fix the firmware.

Offline azslow3

  • Administrator
  • Hero Member
  • *****
  • Posts: 1706
Re: Air Access 18
« Reply #28 on: May 09, 2024, 12:41:41 AM »
I forgot to mention. It is known uploading scene can fail, not every second time but happens, that is a kind of normal. That is the reason for the verification step, which report inconsistency. When there is no errors, AZAOSC has checked that all mixer settings mentioned in the scene are exactly as sent.