Author Topic: [Bassman] Preset for Novation Launch Control XL MKII  (Read 241 times)

Offline Bassman

  • Full Member
  • ***
  • Posts: 139
[Bassman] Preset for Novation Launch Control XL MKII
« on: August 04, 2020, 04:50:34 PM »
HI:)     

Preset for the Novation LaunchControl XL MKII. All commands are described in the PDF.

More than 600 Parameter can be controlled at the moment, without ACT!

Uses 4 Userpresets from Launch control. Upload it with the editor to the Controller (Preset 1-4), to switch between the presets it needs to enable Sysx forwarding in the Cakewalk Settings!

Newest Files: (09-24-2020)

https://1drv.ms/u/s!Al2mKojzOW0Mp6cltmQ69wjk2fKl0A?e=Di36ce

Please give some feedback on this huge preset. It will take time to try all out!

Have fun;)
Bassman.


« Last Edit: September 24, 2020, 01:50:51 PM by Bassman »

Offline Bassman

  • Full Member
  • ***
  • Posts: 139
Re: [Bassman] Preset for Novation Launch Control XL MKII
« Reply #1 on: August 18, 2020, 02:47:51 PM »
Hi:)

Update 09.24.2020

Added in PRV Mode:

Zoom R6, R14, R22
Next/Previous Bar/Marker R 9, R 17
Snap/Note Length Settings R 1, R 2
Move Data Cursor L/R/U/D Slider 1, Slider 2
Do nothing LONG_PRESS Mute 2

Update 23.09.2020

Added Mute 2 Button LONG_PRESS Do nothing with Rotors and Sliders in Normal Mode.

Solo 4 and Mute 4 LEDs now work correctly on LONG_PRESS in Normal Mode.

Update 19.09.2020

Added PRV Mode: (Edit Mode and CTRL + SHIFT ON, just press both)

Change Note Length, Nudge Left/Right/Up/Down, Octave Up/down, Change Note Velocity -1,-5,+1,+5, select Next/Previous Note, Open PRV, Toggle Edit Filter for to see Data Cursor on edited Track


Update 17.09.2020

Added VEL+- Buttons to Edit Mode with CTRL (See PDF)

Cals: Velocity +-3, Velocity +- 1 (changed 3 to 5 points), Keystrokes CTRL+NUM +(-)(3), CTRL+SHIFT+NUM +(-)(1)

Restricted to use LONG_PRESS Solo4 and Mute 4 (WAI change), if CTRL Button is pressed in Edit Mode.

PLAY Button LED is working now correctly after leaving ACT Mode.

Update 16.09.2020

ACT Mode Blinking on Shift and Ctrl Button is now working correctly after hitting Stop.

Preset 1 Bank 4 (ProChannel) Rotor 16 is now Pan of selected Track
Preset 1 Bank 4 (ProChannel) Rotor 24 is now Volume of selected Track
Rotor 16 with Shift in ACT Mode is now Pan of selected Track.
Rotor 24 with Shift in ACT Mode is Volume of selected Track.

Word Files (Graphic with SHIFT and LONG_PRESS Parameter) for Normal Mode are ready (Preset 1, Bank 1-4)

Update 15.09.2020

Solo 5 Long_Press in Normal Mode is now Loop On/Off.

Rotor 23 with Shift in ACT Mode is now Pan of selected Track.
Rotor 24 with Shift in ACT Mode is now Volume of selected Track.

I'm writing Word Files with the parameters of the Normal Mode.

Update 13.09.2020

Restricted to change Preset and Bank in ACT and Level Mode. Level Mode is now only accessible from Preset 1 Bank 1.

Play and Record Buttons now work in all Presets and Banks.

I needed more ACT Parameters so I added all Controls with Shift in Bank 1.

Greetz;)
Bassman.
« Last Edit: September 24, 2020, 01:55:05 PM by Bassman »